ESP-WROOM-32 Espressif ESP 32 ESP 32S IoT Wifi Wlan BLE Module mit Adapter Board

Description: ESP-WROOM-32 Espressif ESP 32 ESP 32S IoT Wifi Wlan BLE Module mit Adapter BoardDescription:ESP-32S ESP32 ModuleESP-WROOM-32 is Powered by Espressif’s most advanced SoC, the ESP-WROOM-32 features high performance, a wide range of peripherals, Wi-Fi and Bluetooth radio, which provide a complete solution tailored to advanced IoT applications.240 MHz dual core Tensilica LX6 microcontroller with 600 DMIPS Integrated 520 KB SRAM Integrated 802.11BGN HT40 Wi-Fi transceiver, baseband, stack and LWIP Integrated dual mode Bluetooth (classic and BLE) 16 MByte flash 2.2V to 3.6V operating voltage -40°C to +125°C operating temperature On-board PCB antenna / IPEX connector for external antenna Supports sniffer, station, softAP and Wi-Fi direct modes Max data rate of 150 Mbps@11n HT40, 72 Mbps@11n HT20, 54 Mbps@11g, and 11 Mbps@11b Maximum transmit power of 19.5 dBm@11b, 16.5 dBm@11g, 15.5 dBm@11n Minimum receiver sensitivity of -98 dBm 135 Mbps UDP sustained throughput 2.5 µA deep sleep current Wi-fi 802.11 b/g/n/e/i 802.11 n (2.4 GHz), up to 150 Mbps 802.11 e: QoS for wireless multimedia technology WMM-PS, UAPSD A-MPDU and A-MSDU aggregation Block ACK Fragmentation and defragmentation Automatic Beacon monitoring/scanning 802.11 i security features: pre-authentication and TSN Wi-Fi Protected Access (WPA)/WPA2/WPA2-Enterprise/Wi-Fi Protected Setup (WPS) Infrastructure BSS Station mode/SoftAP mode Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management UMA compliant and certified Antenna diversity and selection Compliant with Bluetooth v4.2 BR/EDR and BLE specification Bluetooth Class-1, class-2 and class-3 transmitter without external power amplifier Enhanced power control +10 dBm transmitting power NZIF receiver with -98 dBm sensitivity Adaptive Frequency Hopping (AFH) Standard HCI based on SDIO/SPI/UART High speed UART HCI, up to 4 Mbps BT 4.2 controller and host stack Service Discover Protocol (SDP) General Access Profile (GAP) Security Manage Protocol (SMP) Bluetooth Low Energy (BLE) ATT/GATT HID All GATT-based profile supported SPP-Like GATT-based profile BLE Beacon A2DP/AVRCP/SPP, HSP/HFP, RFCOMM CVSD and SBC for audio codec Bluetooth Piconet and Scatternet ESP32 vs ESP8266: ESP32 ESP8266 Ethernet MAC Interface Nicht vorhanden GPIOs fÜr 10 Touch-Sensoren Nicht vorhanden Temperatur-Sensor (on-chip) Nicht vorhanden Remote-Controller-Funktionalität Nicht vorhanden Hall-Sensor Nicht vorhanden Digital-to-Analog Converter (DAC) Nicht vorhanden CAN 2.0 Nicht vorhanden Analog-to-Digital Converter (ADC): 16 Kanäle mit 12-Bit SAR-ADC mit UnterstÜtzung fÜr einen Low-Noise Amplifier (LNA) 10-bit ADC, kein LNA 2 I2C-Schnittstellen 1 I2C-Schnittstelle 16 Kanäle fÜr PWM 8 Kanäle fÜr PWM GPIOs (General-Purpose Input/Output): 36 GPIOs: 17 4 SPI-Schnittstellen mit Quad-SPI und maximal 80 MHz 3 SPI-Schnittstellen mit Quad-SPI und maximal 80 MHz Pinbelegung: Package included:1*ESP-32 ESP-32S ESP-WROOM-32 WLAN & BLE ModuleESP-32S ESP32 AdapterThis is a adapter board for ESP-32S Wireless Module. It can be inserted to breadboard with Dupont cable wire. Convenient to develop and debug. RESET I/O Pins Pin Pitch: 2.54mmPackage included:1*AdapterESP-32/ESP-32S Wifi Module+AdapterPackage included:1*ESP-32 ESP-32S ESP-WROOM-32 WLAN & BLE Module1*AdapterESP-32/ESP-32S Devolopment Board(CP2102)ESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters, and power management module. The entire solution takes up the least amount of printed circuit board area.This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology,power and RF properties best, which is safe, reliable, and scalable to a variety of applications. Features: High performance-price ratioSmall volume, easily embeded to other productsStrong function with support LWIP protocol, FreertosSupporting three modes: AP, STA, and AP+STASupporting Lua program, easily to developPackage included:1 x ESP32 Development Board Payment MathordReturns PolicyAbout FeedbackPayment Mathord 1. PayPal payment accepted only. 2. Items will be shipped to your eBay address. Please make sure it is correct. 3. Payment must be received 4 days after auction ended.Returns Policy 1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase. 2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer. 3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner. 4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response. About Feedback When you satisfied with our product and services please leave us positive feedback. If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay. On 05-Sep-20 at 08:43:23 BST, seller added the following information:On 05-Sep-20 at 09:30:24 BST, seller added the following information:

Price: 0.99 GBP

Location: 深圳, 廣東省

End Time: 2024-08-05T07:37:18.000Z

Shipping Cost: 1.28 GBP