Brompton headset for T Line

Description: This is a replacement headset for the T Line Bromptons The pack consists of:SHR/S - steerer clap ring seal HCR- headset compression ring ACB 30.2mm - Angular Contact BearingsACB 40mm - Angular Contact Bearings Complete with fitting diagram Removal:To separate the steer hinge clamp (SHC) from the fork steer (FS), fold the handlebar support (HBS) to reveal the preload bolt (PB) in the center of the SHCUndo the bolt and remove itUndo all 4 steerer hinge bolts (SHCB) by 3-4 turns - Do not remove completely to prevent the steerer clamp plate SCP from falling out, then gently twist the SHC and pull upwards to separate it from the fork steerer (FS) Fitting:Lightly grease all bearings and mating surfaces, before fitting, this includes the headset, the steerer hinge clamp and the head of the boltsYou should also grease the inside of the fork steererAvoid getting grease on the clamping surfaces! Fit the 40MM headset angular contact bearing ACB on the fork - do not forget to grease!Fit the other angular contact bearing (ACB) - the 30.2MM in the top cup of the headtube (HT), grease lightly, followed by the headset compression ring (HCR)Insert the fork steerer into the head tube (HT), ensuring that all parts are aligned and seated correctlyFit the steerer clamp ring seal (SCR)Fit the steerer head clamp (SHC) body over the fork steerer (FS); insert and tighten preload the preload bolt (PB) to 3NmUnfold the handlebar support HBS and align the handlebar to the front wheelPartially tighten the two right steerer clamp hinge bolts SHCB looking towards the front of the bike followed by the two left boltsCheck that the handlebar is in alignment with the front wheelThis is best out of the standTighten the 2 right Steerer head clamp bolts (SHCB) to 4Nm followed by the two left bolts (left and right when looking at the bike)The Correct torque is very important to ensure that the handlebars do not twist in use!!!It is vital that you apply the correct torque. If the bolts are not tightened enough, the handlebars could twist in use, if over-tightened you could be damaged Ensure the cables are routed around the non-drive side of the Handlebar support (HBS)Check the position of the handlebar catch! Introduced in 2022 Notes:It is vital that you follow the correct fitting procedure Do not try to adjust the steerer stop band (SSB) as this requires a special toolThis in not compatible with pre-2022 A, C or P Line Bromptons bikes To separate the steer hinge clamp (SHC) from the fork steer (FS), fold the handlebar support (HBS) to reveal the preload bolt (PB) in the center of the SHC Undo all 4 steerer hinge bolts (SHCB) by 3-4 turns - Do not remove completely to prevent the steerer clamp plate SCP from falling out, then gently twist the SHC and pull upwards to separate it from the fork steerer (FS) Lightly grease all bearings and mating surfaces, before fitting, this includes the headset, the steerer hinge clamp and the head of the bolts Fit the other angular contact bearing (ACB) - the 30.2MM in the top cup of the headtube (HT), grease lightly, followed by the headset compression ring (HCR) It is vital that you apply the correct torque. If the bolts are not tightened enough, the handlebars could twist in use, if oTo separate the steer hinge clamp (SHC) from the fork steer (FS), fold the handlebar support (HBS) to reveal the preload bolt (PB) in the center of the SHC Undo all 4 steerer hinge bolts (SHCB) by 3-4 turns - Do not remove completely to prevent the steerer clamp plate SCP from falling out, then gently twist the SHC and pull upwards to separate it from the fork steerer (FS) Lightly grease all bearings and mating surfaces, before fitting, this includes the headset, the steerer hinge clamp and the head of the bolts Fit the other angular contact bearing (ACB) - the 30.2MM in the top cup of the headtube (HT), grease lightly, followed by the headset compression ring (HCR) It is vital that you apply the correct torque. If the bolts are not tightened enough, the handlebars could twist in use, if o

Price: 168.19 USD

Location: London

End Time: 2024-11-16T00:26:48.000Z

Shipping Cost: 13.68 USD