1960's-1980's Gibson-Bruce Guitar Case Handle fits Les Paul es 335 sg 175 flying

Description: from RetroGuitarParts vintage guitars + parts "Jazz and Archtop Specialist" Black Bruce handle -new old stock...as used on many vintage Gibson cases Correct for some 1970's through1980s Gibson cases... see last pic: a 1984 Les Paul case with red interior Auction includes handle --- and 2 brass mounting axle pins in the hard to find size of 7/8". ....allows you to retain your original hardware plates on some cases. Check out the pics and measurements before bidding please! This is a "NOS" USA-made vintage BRUCE handle...limited quantity....these have been out of production for decades. This is a “pre-Nashville” Gibson "Bruce" handle.....new-old-stock...with 2 TKL axles....allows you to retain your pre-existing hardware on the Gibson-Lifton cases and reissue cases from the 1970's on, when nickel hardware was used ....for the Les Paul model, SG, L6, and es 335 model case, etc. ....looks great! When you are finished, you can barely tell it was replaced. Also works great on older 60's cases! These were made in the USA....no longer available!! The axle type is the 'spinning' type. If you are concerned if this will fit your pre-existing hardware, send me a pic of your case. BLACK HANDLE COMES WITH solid brass 7/8" SPINNING AXLES. Features....black plastic handle with vintage Faux Stitching...correct for many earlier Gibson cases and thier reissue caseMint condition...has not been previously installedFrom the 70s, but can be used on many Gibson casesgreat vintage looksMeasuring from center of leg to center of leg is 4.25 inches .... this is a perfect size replacement for almost all years of the Gibson cases...the standard Gibson measurement has been approximately 4.25 to 4.5 inches since the 40's! Please measure your case hardware before bidding; measure from center of hardware to center of hardware. Comes with 2 "spinning" axles. (installation instructions below) See close up pic of the axles......open ends are ball-peined to close...see directions below Case handle is excellent quality molded plastic. I have used these to restore many cases with good results. Please confirm your measurement requirement before bidding: Measuring from center of leg to center of leg is 4 and 1/4 inches...this is a perfect replacement for some of the reissue cases...may be able to be used on other years of the Gibson-Lifton cases when you require a handle that is approximately 4.25 (Measuring from mounting bracket to center of mounting bracket). This kit allows you to retain the original case hardware on some cases, if it is still there! Please measure your case hardware before bidding; measure from center of hardware to center of hardware. The type of axle included is the 'spinning' type. (Does not fit the heavier old-style Lifton brackets that use a 'fixed' axle). Email me with a pic of your case if you are unsure! SHOP TALK: AXLE PIN INSTALLATION AXLE PIN INSTALLATION (Spinning axles): Cut off the old pins if they are still there, with wire-cutters. Insert the new pin into the handle and hardware on the case. The open end of the axles should both face to the INSIDE of the handle. Hold a counter weight or small anvil on the opposite end of the axle than what you are tapping on. Use a ballpein hammer to lightly tap around the edges of the pin end that is open. You are basically creating a 'burr' that locks the pin. Continue tapping around the edges until it evenly folds down and looks like the other end. When you are done, both ends will look about the same with a head that is larger than the original hole, locking the pin in place. Word of Caution: DO NOT HAMMER THE END because the pin can bend. Light tapping is required and it takes a little time. It will give a professional result if you take your time and use light tapping around the opening. On cases that have the original brackets mounted at extreme angles on the upper and lower bouts (where the brackets seem to point in different directions), this handle gives you a little bit better chance of having a fit, since the holes in each leg are oval in shape, giving you some wiggle room to mount at odd angles. Some cases with brackets mounted at extreme planes are difficult to fit. Email pictures if you are unsure..i will always try to help you get a handle back on your case! Nice for vintage case repair projects. Please check out our other case repair parts! Shipping adds 5.50 usa New International Shipping Policy Now shipping internationally with full insurance for a rate of 22 USD USD..... this cost accounts for the greater amount of time, materials, risk, and insurance cost that are all necessary when we ship internationally. International Buyers – Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. You are responsible for any customs fees that your country adds during the importation process. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. This auction is for just the handle and 2 axles...no mounting plates...so you can retain your original hardware…..this auction includes just the black handle with two axles pins

Price: 16.99 USD

Location: Smithfield, Rhode Island

End Time: 2024-09-19T13:46:38.000Z

Shipping Cost: 5.5 USD